Lightolier C7CW Manuel d'utilisateur télécharger pdf

MULLION

OUTLET BOX SCREWS

MOUNTING PLATE

CANOPY

1/4-20 BOLTS

CLEAT

GASKET

CLEAT

FIG. 4

FIG. 3

FIG. 2FIG. 1

A COMPANY

631 Airport Road, Fall River, MA 02720

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To

assure full compliance with local codes and regulations, check with your local electrical inspector before

installation. To prevent electric shock, turn off electricity at fuse box before proceeding.

Retain these instructi

ons for maintenance reference.

INSTRUCTION SHEET NO.

IS:C7CW

Page 1 of 2

A0604

CAUTION: For wet locations, in accordance with Underwriters Laboratories

requirements, a line of caulking compound such as acrylic or silicone must be

placed around the perimeter of CANOPY to seal water away from the

outlet box and back openings. Use only compatible REFLECTOR TRIMS

rated for use in Wet Locations.

INSTALLATION OF WALL CYLINDER TO OUTLET BOX

(Fig. 1, 2, 3, & 4)

STEP 1:

Attach MOUNTING PLATE to outlet box with OUTLET BOX

SCREWS.

STEP 2: Pass supply leads through opening in CANOPY and CLEAT.

STEP 3: Attach CANOPY and CLEAT to MOUNTING PLATE with (2) ¼-20

BOLTS (provided).

STEP 4: Make Connections. Bare Copper and/or green insulation wire(s)

must be connected to SUPPLY GROUND. Connect WHITE BALLAST LEAD

to NEUTRAL (WHITE) SUPPLY LEAD. Connect BLACK BALLAST LEAD to

HOT SUPPLY LEAD. Use wire nuts (local hardware items).

STEP 5: Install SET SCREWS loosely. Push excess supply leads back into

outlet box. Place cylinder over CLEAT and tighten (2) SET SCREWS.

INSTALLATION OF WALL CYLINDER TO POST OR OTHER

VERTICAL SURFACE MOUNTING (Fig. 2, 3 & 4)

1. CLEAT can also be mounted directly to any flat surface such as

MULLION. In this case, use of CANOPY is optional. Bring supply

leads through CLEAT and install CLEAT to wall. For wet locations, in

accordance with Underwriters Laboratories requirements, a line of

caulking compound such as acrylic or silicone must be placed around

the perimeter of EXTRUDED ARM to seal water away from the

wireway and back openings.

2. Proceed with Step 4 and 5 above.

INSTALLATION OF REFLECTOR TRIM TO CYLINDER (Fig. 4)

Follow installation instructions in Reflector Trim Instruction Sheet.

CAUTION:

 DO NOT ENERGIZE THE LAMP UNTIL

REFLECTOR TRIM IS COMPLETELY INSTALLED.

WARNING: USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURERS’

REFLECTOR TRIMS MAY VOID THE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.

INSTALLATION PROCEDURE FOR: C7CW SERIES 7” DIA. H.I.D. WALL CYLINDER

USED WITH C7E17VM, C7E17OVM, C7P38MH, C7E17PL, C7E17FL SERIES FLANGLESS

REFLECTOR TRIM (ORDER SEPARATELY)

1 2

IS:C7CW 1

Résumé du contenu

Page 1 - IS:C7CW

MULLIONOUTLET BOX SCREWSMOUNTING PLATECANOPY1/4-20 BOLTSCLEATGASKETCLEATFIG. 4FIG. 3FIG.

Page 2

FIG. 5TO REPLACE BALLAST (Fig. 5 & 6) Before changing the ballast, switch off the main power supply to the fixture. STEP 1: Remove lamp. STEP

Commentaires sur ces manuels

Pas de commentaire

Lightolier C7CW Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Lampes de travail Lightolier C7CW. Lightolier C7CW User's Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Lampes de travail Lightolier C7CW